不銹鋼電解拋光劑，不銹鋼電解拋光液 - 產品詳情
| 分類
|
不銹鋼清洗劑 |
香型
|
無 |
| PH值
|
2 |
保質期
|
24（月） |
| CAS
|
無 |
|
|
508不銹鋼電解拋光劑：一、本品性能：能快速有效地將金屬工件內管、內腔表面的凹坑、毛刺等通過電解方式整平拋亮，本品主要由腐蝕劑(由無機弱酸、有機酸組成)、緩蝕劑、光亮劑、酸霧抑制劑等成分合成，工作時無煙霧和刺激性氣味產生，主要針對形狀復雜、機械拋光和化學拋光方式無法達到拋光要求的工件而設計，屬于陽極電解。本品對去除氬弧焊所產生的焊斑等高溫氧化物也有非常好的效果，能保證色澤光亮均一、不發白，優于傳統的洗鋼水。二、本品特點：1.藥液穩定，不易分解老化，消耗量低，使用壽命超出傳統拋光劑的一倍；2.不含強酸（如硫酸）、鉻酸、氯化物、氟化物等，故對皮膚、工件和設備腐蝕性極小，對環境無污染；3.能拋出光亮、平滑、均一的鏡面光澤效果，防銹能力強，光澤持久；4.在使用本劑拋光前建議先將金屬表面的銹斑、油污等進行預先處理，以節省本劑。三、物理指標：透明液體或微黃色液體，密度（g/cm3）：1.82±0.02，PH=2.0±0.02四、適用范圍：本品適用于304、316、316L等大多數不銹鋼的鏡面拋光。五、使用方法：不需加入任何其它添加劑即可使用（原液使用），適當添加20-30%硫酸拋光效果會更佳。鈦板、鉛板或不銹鋼板做陰極（負極），工件做陽極（正極），建議陽級緩慢移動，并適當攪拌避免局部過熱，以下為使用工藝參數：溶液使用溫度陽極電流密度電壓陰極∶陽極面積操作時間40-80度3-30安培/平方分米6-25伏至少2∶13-10分鐘溫度60度為佳，工件體積大設計電流、電壓大，工作時間長六、操作流程：上掛→化學除油→熱水洗→冷水洗→電解拋光→二次流動冷水洗→酸活化（5%硫酸水溶液）→流動冷水洗→干燥（可根據實際情況，調整部分工藝流程）。七、注意事項：1、工作液具有一定的腐蝕性，不宜與裸露皮膚接觸，操作時應佩帶乳膠手套；2、處理件油污嚴重時，建議預作粗荒除油；3、工作液處理一段時間后，由于有效濃度下降，處理效果不佳，此時應更換新液或補加本品；4、應在通風良好之場所進行操作。八、包裝規格與運輸：塑料桶包裝30kg/桶，按一般化學品運輸，輕裝輕卸，防止重壓倒置。貯于室溫下通風處。保質期壹年。九、廢液處理：用堿水或石灰水中和至中性LJ-508 stainless steel electrolysis polisher：1.PerformanceThe product can smoothen and brighten the inner tube, concavity on the inner surface and burr of metal pieces quickly and effectively via electroanalysis.No pungent smog or smell when operating.Designed for the workpiece with complex shape which mechanical polishing and chemical polishing aren’t cable to deal with.2.CharactericticsStable,not easy to disintegrate and aging,low consumptionNot include strong acid,no pollution to the environmentCan get the bright,smooth and uniform surface,strong capability to prevent rust,permanent polishSuggest to foreclose the rust or oil on the surface of metal pieces before using this product to save the polisher3.Physical specsTransparent or kelly liquid,density is 1.62±0.02g/cm3, PH=2.0±0.024.Scope of applicationApplicable for 304、316、316L etc stainless steel polishing5.UsageNo need to add other additive normally,can get better effect if add 20-30% vitriol.Titanium board,leading or stainless steel board as cathode,workpiece as anode.Seggest to move the anode slowly and mix round to avoid partial with high temperature.Below is the technical parameters.TempCurrent density of anodeVoltageArea rate of cathode toanodeTime40-80 DgreeA/sq.dm6-25 V2∶1At least3-10 minThe best temp. is 60℃,greater current and voltage and longer time if large workpieces6.Operation processHanging—Chemical deoiling—Washing with hot water-- Washing with cool water--Electrolysis polishing-- Washing with cool water—Activition with 5% vitriol solution—Flow water washing--Drying7.CautionPlease don’t touch with the bare skin.To wear latex gloves when operatingThe oil must be removed completely before using the productAdd more product or replace with the new after working a periodPlease use the product under the airy circumstancePlease make operating liquid cool before add vitriol,or it will splash to cause the danger8.Package & TransportationPlastic bucket,30kg/bucket.Transport as normal chemical.Load and unload lightly.Don’t stress and inversion.Store inairy circumstance. Shelf life is 1 year.
